2元彩票

National Advisory Service Hotline: 400-6700-720 / 020-38937005

Position: 2元彩票 > Products > PC > LEXAN > pc-lexan >

Sabic Lexan PC HP1-1H112

2016-11-14 09:21

Lexan PC HP1

Medical and health related uses. Controllable viscosity, color and dopant. Meets FDA tripartite (ISO 10993-1 revision) / USP Class VI specifications. Demolding.

machining

Injection -USA

 Melt temperature 520-560 deg F Nozzle temperature 510-550 deg F Front temperature 520-560 deg F Middle temperature 500-540 deg F Rear temperature 480-520 deg F Mold temperature 160-200 deg F Drying temperature 250 deg F Drying time (minimum) 3-4 h Drying time (maximum) 48 h Back pressure 50-100 psi Screw speed 40-70 rpm Recommended injection volume 40-60% Exhaust groove depth 0.0010-0.0030 in 

Medical and health related uses. Controllable viscosity, color and dopant. Meets FDA tripartite (ISO 10993-1 revision) / USP Class VI specifications. Demolding.

performance

mechanical

performance

Typical data

unit

method

Tensile Strength , Yield, Type I, 0.125 "

9000

psi

ASTM D 638

Tensile Strength , Fracture, Type I, 0.125 "

9500

psi

ASTM D 638

Tensile Extension , Yield, Type I 0.125 "

6.0

%

ASTM D 638

Tensile Extension , Break Type I 0.125 "

120.0

%

ASTM D 638

Tensile Modulus , Type I, 0.125 "

345000

psi

ASTM D 638

Flexural Strength , Yield, 0.125 "

13500

psi

ASTM D 790

Flexural Modulus , 0.125 "

335000

psi

ASTM D 790

Compressive strength

12500

psi

ASTM D 695

Compression modulus

345000

psi

ASTM D 695

Shear strength

6000

psi

ASTM D 732

Shear modulus

114000

psi

ASTM D 4065

Hardness , Rockwell M

70

-

ASTM D 785

Hardness , Rockwell R

118

-

ASTM D 785

Taber Abrasion , CS-17, 1 kg

10

mg / 1000cy

ASTM D 1044

Fatigue limit , 2.5 MM cycle

1000

psi

ASTM D 671

Shock

performance

Typical data

unit

method

Izod impact value , no gap, 73F

60.0

ft-lb / in

ASTM D 4812

Izod impact value , notch (natural, light)

12.0

ft-lb / in

ASTM D 256

Izod impact value , notch (color)

2-12

ft-lb / in

ASTM D 256

Tensile impact value , type "S"

180

ft-lb / in2

ASTM D 1822

Dart impact value (D 3029), 73F

125

ft-lbs

ASTM D 3029

Instrumentation Control Shock Energy @ Peak, 73F

480

in-lbs

ASTM D 3763

heat

performance

Typical data

unit

method

(热畸变温度) , 66 psi, 0.250", 未退火 HDT (thermal distortion temperature) , 66 psi, 0.250 ", unannealed

280

deg F

ASTM D 648

(热畸变温度) , 264 psi, 0.250", 未退火 HDT (thermal distortion temperature) , 264 psi, 0.250 ", unannealed

260

deg F

ASTM D 648

Thermal conductivity

0.19

W / mC

ASTM C 177

, -40F ~ 200F CTE (Coefficient of Thermal Expansion), flow , -40F ~ 200F

3 E-5

in / in-F

ASTM E 831

Specific heat

0.30

BTU / lb-F

ASTM C 351

Thermal index

125

deg C

UL 746B

Thermal index, mechanical impact performance

115

deg C

UL 746B

Thermal index, non-mechanical impact performance

125

deg C

UL 746B

Brittle temperature

-200

deg F

ASTM D 746

physical

performance

Typical data

unit

method

Specific gravity, solid

1.20

-

ASTM D 792

specific volume

23.10

in3 / lb

ASTM D 792

density

0.043

lb / in3

ASTM D 792

Water absorption , 24 hours @ 73F

0.150

%

ASTM D 570

Water absorption , equilibrium, 73F

0.35

%

ASTM D 570

Water absorption , equilibrium, 212F

0.58

%

ASTM D 570

Mold Shrinkage , flow, 0.125 "

5-7

in / in E-3

ASTM D 955

Melt flow rate , nominal, 300C / 1.2 kgf (O)

25.0

g / 10 min

ASTM D 1238

Optics

performance

Typical data

unit

method

Light Transmission , 0.100 "

88.0

%

ASTM D 1003

Haze , 0.100 "

1.0

%

ASTM D 1003

Refractive index

1.586

-

ASTM D 542

Electricity

performance

Typical data

unit

method

Volume resistivity

> 1E17

ohm-cm

ASTM D 257

Dielectric strength in air , 125 mils

380

V / mil

ASTM D 149

Dielectric constant , 60 Hz

3.17

-

ASTM D 150

Dielectric constant , 1 MHz

2.96

-

ASTM D 150

Loss factor , 60 Hz

0.0009

-

ASTM D 150

Loss factor , 1 MHz

0.0100

-

ASTM D 150

Flame characteristics

performance

Typical data

unit

method

UL file number, USA

E121562

-

-

V-2 rating (test thickness)

0.043

inch

UL 94


Previous: Lexan PC XHT4141
Next: Lexan PC HP4

Working with Plastic Engine

You will get more mature professional engineering plastics supply services. We put customers first, and also actively challenge, and strive to present the best service quality to our customers.

Engineering Plastics Hotline:

400-6700-720
020-38937005

About Plastic Engine:
AG真人网 真人斗牛app 电玩竞技游戏 真人斗牛app 电玩游戏平台 电玩竞技游戏 皇冠体育官网 博狗直营